M5Stack Fire

• V

  Fire getBatteryLevel()
  • Veto6017

  2
  0
  Votes
  2
  Posts
  170
  Views

  

  Hello @Veto6017 hmm, with an M5Stack Fire (HW: 2018.2A) running your code I get "Power canControl OK". Have you tried to run I2C_Tester.ino? The I2C scan finds 0x10 (BMM150), 0x68 (MPU6886) and 0x75 (IP5306). Thanks Felix
• C

  Error in access SD card
  • CA_HeArc

  2
  0
  Votes
  2
  Posts
  355
  Views

  C

  Edit: is there any limit in size for the SD cards ? if so, what is it ? Best regards, C.A.
• H

  Serial Coms issue with jetson nano
  • hetzer

  1
  0
  Votes
  1
  Posts
  701
  Views

  No one has replied

• C

  M5Stack Fire Turning Off After A Few Seconds
  • codewitch

  2
  0
  Votes
  2
  Posts
  861
  Views

  

  Hello @codewitch have you tried keeping it plugged in for a while to charge the battery? have you tried to run it w/o battery, e.g. with the M5GO bottom removed? Thanks Felix
• H

  Speaker Buzzing and Popping
  • HWTaro9

  1
  1
  Votes
  1
  Posts
  797
  Views

  No one has replied

• H

  Port D and E?
  • HWTaro9

  3
  0
  Votes
  3
  Posts
  1117
  Views

  H

  @ajb2k3 thank you!
• D

  ENV III not connected message
  • dartec

  2
  0
  Votes
  2
  Posts
  945
  Views

  

  Is the ENV III plugged into the red port?
• 

  How to program the M5stack fire RGB LEDs SK6812
  • grelm

  5
  0
  Votes
  5
  Posts
  6164
  Views

  

  @ajb2k3 No it's not a Grove pin. Check here: https://github.com/m5stack/m5-docs/blob/master/docs/en/core/fire.md
• 

  Bootloop
  • Kabron

  3
  0
  Votes
  3
  Posts
  2294
  Views

  

  Right, OK, nobody panic! There is a bug somewhere that causes a random boot loop to appear in the ESP32 and strangely I had this with a Stamp the other weekend. Disconnect everything and leave the controllers unconnected for a while, cold boot the computer and try and flash UIFLow firmware.
• R

  M5Stack Fire battery LED blinking - no function of the core
  • ramaker

  4
  0
  Votes
  4
  Posts
  3753
  Views

  D

  Hello had the same problem. Solution with me, Use an older 5V USB power supply. The new ones switch off due to insufficient power consumption. Motorola review 2020 low A. = off Samsung v. 2015 no problem. Try old power supplies without high-performance charge control. 73/ Klaus
• 

  DO-UNTIL loop
  • mathias

  3
  0
  Votes
  3
  Posts
  2821
  Views

  

  Hey robalstona, Thanks for your answer. You are right this could be the problem. I will try it out in the near future. cheers, Mathias
• M

  M5StickC power managment
  • Mohir

  1
  0
  Votes
  1
  Posts
  1761
  Views

  No one has replied

• A

  platformio error with M5.IMU.INIT
  • amn

  3
  0
  Votes
  3
  Posts
  3064
  Views

  A

  Solved comment M5stack.h: //#include <M5Stack.h> #define M5STACK_MPU6886 thx
• A

  M5Stack Fire core + Plus + M5GO base = psram fails on boot
  • anichang

  2
  0
  Votes
  2
  Posts
  2236
  Views

  

  Hello @anichang just wondering - maybe the issue isn't specific to PSRAM but with the power supply? I'd try a different power supply and/or shorter USB cable. Thanks Felix
• 

  M5stack Fire bricked !!!
  • teddygag

  3
  0
  Votes
  3
  Posts
  3366
  Views

  

  1st thing to do is DON'T Panic! Next remove the base and module leaving only the firecore. Plug a usb cable in and connect just the core section into a computer, go into hardware reports and check usb devices. Do you have a USB to UART adapter? Try the instructions on this page to use an external adapter https://docs.m5stack.com/#/en/tool/usb_downloader?id=esp32-downloader
• U

  M5Stack FIRE - no module named 'ntptime'
  • uniko92

  2
  0
  Votes
  2
  Posts
  2255
  Views

  

  @uniko92 Firmware on the Fire is really old. Please use M5Burner to upgrade it to 1.7.4.
• M

  M5Stack FIRE not returning any data from Gyro or Accel with MPU 6886
  • marek

  1
  0
  Votes
  1
  Posts
  1925
  Views

  No one has replied

• A

  m5stack fire black screen after i conected servo motor to it
  fire • • abdullrhman

  3
  1
  Votes
  3
  Posts
  3184
  Views

  A

  @m5stack , @ajb2k3 sorry but any ideas?
• C

  M5Stack Fire - Error when selecting the way to program it
  • Carles B.

  9
  0
  Votes
  9
  Posts
  6044
  Views

  

  @carles-b Great. Glad you got it sorted out and can begin enjoying M5Stack 😀
• A

  Import error("no module named 'uiflow' ", ) displayed on the M5Stack
  • Alpine-Lake

  6
  0
  Votes
  6
  Posts
  7315
  Views

  C

  @sodoku Thanks a lot. That solved my problem. Seems my Core came with a very old software image. In the M5Flow Menu there's a very helpful video on how to flash. It took me 10 minutes and now I'm having fun with my core.