Problem has been solved
The weak USB cable was to blame, after replacing the cable with the original Samsung, the problem did not return.
Problem messages are:
"BrownOut detector was triggered" and
"The Guru Meditation" something like Blue screen of Death (BSOD)
Posts made by spairo
-
RE: M5Stack after loading the program is still restarting.
-
RE: M5Stack after loading the program is still restarting.
after download m5stack-ble black box is resrating in loop with register dump.
Rebooting...
ets Jun 8 2016 00:22:57rst:0xc (SW_CPU_RESET),boot:0x17 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:1
load:0x3fff0018,len:4
load:0x3fff001c,len:1216
ho 0 tail 12 room 4
load:0x40078000,len:9720
ho 0 tail 12 room 4
load:0x40080400,len:6352
entry 0x400806b8
M5Stack initializing...OK
Guru Meditation Error: Core 0 panic'ed (LoadProhibited). Exception was unhandled.
Core 0 register dump:
PC : 0x4010512d PS : 0x00050031 A0 : 0x4008565c A1 : 0x3ffbe360
A2 : 0x00000000 A3 : 0x3ff48044 A4 : 0x800e04be A5 : 0x400916e8
A6 : 0x00000000 A7 : 0x40085fb0 A8 : 0x00000000 A9 : 0x3ffbb700
A10 : 0x00000000 A11 : 0x3ffbbd60 A12 : 0x800e04b3 A13 : 0x3ffbc010
A14 : 0x00000000 A15 : 0x3ffbc03f SAR : 0x00000016 EXCCAUSE: 0x0000001c
EXCVADDR: 0x00000000 LBEG : 0x00000000 LEND : 0x00000000 LCOUNT : 0x00000000
Core 0 was running in ISR context:
EPC1 : 0x4010512d EPC2 : 0x00000000 EPC3 : 0x00000000 EPC4 : 0x00000000Backtrace: 0x4010512d:0x3ffbe360 0x40085659:0x3ffbe380 0x40185037:0x3ffbc060 0x400e1a02:0x3ffbc080 0x40090745:0x3ffbc0a0 0x4008ef51:0x3ffbc0c0
Rebooting...
ets Jun 8 2016 00:22:57rst:0xc (SW_CPU_RESET),boot:0x17 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:1
load:0x3fff0018,len:4
load:0x3fff001c,len:1216
ho 0 tail 12 room 4
load:0x40078000,len:9720
ho 0 tail 12 room 4
load:0x40080400,len:6352
entry 0x400806b8
M5Stack initializing...OK
Guru Meditation Error: Core 0 panic'ed (LoadProhibited). Exception was unhandled.
Core 0 register dump:
PC : 0x4010512d PS : 0x00050031 A0 : 0x4008565c A1 : 0x3ffbe360
A2 : 0x00000000 A3 : 0x3ff48044 A4 : 0x800e04be A5 : 0x400916e8
A6 : 0x00000000 A7 : 0x40085fb0 A8 : 0x00000000 A9 : 0x3ffbb700
A10 : 0x00000000 A11 : 0x3ffbbd60 A12 : 0x800e04b3 A13 : 0x3ffbc010
A14 : 0x00000000 A15 : 0x3ffbc03f SAR : 0x00000016 EXCCAUSE: 0x0000001c
EXCVADDR: 0x00000000 LBEG : 0x00000000 LEND : 0x00000000 LCOUNT : 0x00000000
Core 0 was running in ISR context:
EPC1 : 0x4010512d EPC2 : 0x00000000 EPC3 : 0x00000000 EPC4 : 0x00000000Backtrace: 0x4010512d:0x3ffbe360 0x40085659:0x3ffbe380 0x40185037:0x3ffbc060 0x400e1a02:0x3ffbc080 0x40090745:0x3ffbc0a0 0x4008ef51:0x3ffbc0c0
Rebooting...
ets Jun 8 2016 00:22:57 -
RE: AT Commands for classic bluetooth
I'm making an interface on the M5stack to the car.
I purchased the Vgate iCAR Pro BLE 4.0 interface and installed the BT terminal on the phone.
Through this terminal he tries to send all the codes to the car and see what comes back.
In my opinion it's the only way not to burn yourself.
iCAR Pro BLE 4.0 also supports BL 2.0 and bl 3.0
Below are the codes that I have already decrypted to establish the transmission between the interface and the carString commandQueue[commandQueueCount] = {
"AT Z", // Reset all
"AT I", // Print the version ID
"AT E0", // Echo off
"AT L0", // Linefeeds off
"AT S0", // Printing of spaces on
"AT H0" // Headers off, on in (debug only)
// Loop from (Alfa Romeo GULIETTA)"AT PP2CSV01" // 01 == CAN 29 ISO 15765-4, fixed DLC 8 byte, 7 orders <commandQueueLoopFrom> "AT PP2CON" // Write to eeprom "AT PP2DSV0A" // baud rate == 500 / yy "0A" == 50 kbps "AT PP2DON" // save eeprom "AT Z" // Reset all ?? ATWS "AT SPB" // set USER1 protocol "AT DP" // Vgate send CAN29/50 ?? ATDPN "AT CRA" // reset all filters "AT CP18" // set CAN priority bit to 18 "AT CRA18DAF140" // set the CAN Rx address to 18DAF140 "AT SHDA40F1" // set the Tx Header to DA40F1 "AT AT0" // adaptive timing control == disable, AT1 == enable "AT ST19" // set timeout in 4 msec steps. 0x19 == 100 msec "AT CAF0" // auto formatting OFF, 8 byte,
};
-
RE: M5Stack after loading the program is still restarting.
I have m5Stack, a small black box with three silver keys and a TFT LCD display.
I can't load anything into m5sstack if I don't give G0 then GND.
I use 7 Pro x32 Win and I use Arduino 1.8.8 or 1.812.
I don't know any other way to program m5Stack under Windows -
M5Stack after loading the program is still restarting.
I have M5Stack.
When I compile my program for Arduino 1.8.12, windows 7 32 bit and I do download with G0 = gnd with a speed of 115200, the program restarts in a circle.
Other speeds don't work.
below the log from the terminalrst:0x1 (POWERON_RESET),boot:0x17 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:1
load:0x3fff0018,len:4
load:0x3fff001c,len:1216
ho 0 tail 12 room 4
load:0x40078000,len:9720
ho 0 tail 12 room 4
load:0x40080400,len:6352
entry 0x400806b8M5Stack initializing...<0><0><0><0><0><0><0><0><0>
Booting device...
Reading settings from eeprom.
Settings not found. Initialization.
Settings saved to eeprom.
Init TFT display
merged:6101FFF8000009285A3B0648030000B4179D763404080805000000
merged:62B002E0000000FFB400330B0000000000000000
Start BLE with PIN auth
ets Jun 8 2016 00:22:57rst:0xc (SW_CPU_RESET),boot:0x17 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:1
load:0x3fff0018,len:4
load:0x3fff001c,len:1216
ho 0 tail 12 room 4
load:0x40078000,len:9720
ho 0 tail 12 room 4
load:0x40080400,len:6352
entry 0x400806b8M5Stack initializing...<0><0><0><0><0><0><0><0><0>
Booting device...
Reading settings from eeprom.
Settings not found. Initialization.
Settings saved to eeprom.
Init TFT display
merged:6101FFF8000009285A3B0648030000B4179D763404080805000000.........