Posts made by KjaerN

KjaerN

Ok, but thank you for loking into it anyway.

Best regards
Kenneth

KjaerN

Thanks again.
Yes, indeed, it is set to high (3.3v between ground and gpio9). And that is the case both when connected to powersupply and pc.
I have an old FTD1232 (FT232RL I think it is), for uploading sketches to some old arduino pro mini boards. But I have never used it for debugging purposes, and have not used it for years. So not sure how to get that debug info out.
I have tried with the Python serial module, but non of the listed ports in device manager will allow me to connect.

The bord I have uploaded this to:
https://github.com/leCandas/M5Stamp-C3

gives the following error in the serial output, but continious executing the expected code:
22:52:51.175 > Build:Feb 7 2021
22:52:51.176 > rst:0x15 (USB_UART_CHIP_RESET),boot:0xd (SPI_FAST_FLASH_BOOT)
22:52:51.176 > Saved PC:0x40385a1c
22:52:51.176 > SPIWP:0xee
22:52:51.178 > mode:DIO, clock div:1
22:52:51.180 > load:0x3fcd6100,len:0x38c
22:52:51.182 > load:0x403ce000,len:0x6a8
22:52:51.185 > load:0x403d0000,len:0x236c
22:52:51.190 > SHA-256 comparison failed:
22:52:51.194 > Calculated: 86b6856493d23fe741a1623c3d149a38bdf91ca0101173d85f25c3fdb6d605ee
22:52:51.200 > Expected: e7bbd322b12b609ed444a0547cebdc54bbcf46aefed1e04449d9827791f3e8ab
22:52:51.203 > Attempting to boot anyway...
22:52:51.205 > entry 0x403ce000

But given the ones I havent put anything on is failing, I think that should be understood first.

Best regards
Kenneth

KjaerN

Hello @felmue

Well, that was also the beahviour I would expect.
so I just pulled the last "untuched" board out of the foil, and plugged it straight into a usb charger. But still nothing happens, when I press either buttons.
But yes, I had also tried the reset button with the other boards.

Then I plugged this new one into my pc, and it emidiatly worked.
Really strange. And unfortunatly not that usefull for the application I had in mind, if it only runs when hooked up to a pc.

Thanks for the reply, and for the input specs.
Kenneth

KjaerN

Hi M5Stack.

I have a sligt problem powering on the M5Stamp c3u devises I got.
I have a package of 5, and none of them (so far tested 4) seems to run the standart progam that comes on the board, when not pluged into a computer.
I.e., if I either hook its 5v and ground pins up directly, or if I hook it up to a usb charger. The same board however works fine when usb is connected to my computer.
I also have a M5Stamp c3 which works when hooked up to pins, and to external usb powersupply.

So far I have not installed the suggested drivers on my computer, since I managed to program this following example on my first attemt (and because I want to use platform IO and not the arduino IDE).
https://github.com/leCandas/M5Stamp-C3
But since the behaviour is also present on the bords I have not used, I dont think that is related.

Also what is the accepted voltage range on the 5v input, I cant seem to find it on the documentation page https://docs.m5stack.com/en/core/stamp_c3u?

Best regards
Kenneth

KjaerN

Hi Felix.

Thaks for your repply, and sorry for my late resonse.
I had some issues logging in again after I created my account.

Your links got the example code to at least build.
But once uploaded to the board I never get past "Connect Error" in the setup.

I have two hats, and two M5StickCPlus, and same issue on both.
So guess I still have some troubleshuting to do.

KjaerN

Hi.

When I follow the link for the arduino examples in the 8Servos Hat documentation pages I get an 404 error.
I.e. the links found on this page:
https://docs.m5stack.com/en/hat/hat_8servos_1.1

And in deed, they seems to be missing from the repository.

But in another local project (platform io), I can see that the folders exists in the .pio example section.
However there (in the 8SERVO_V1.1 example), it tries to include a HAT_8SERVO.h file, which seems to be missing from the example folder.

Is there a better location I should go to, to find this example?
Or has this file simply just been forgotten in a commit?
(Or am I simply missing a include library or somthing?)

I hope you can help getting me past this issue.