thx Adam....As you said I found it..
I still do not know why it is not workimg with atom s3
voila
3d printing hobbyist actively designing stuff.. I own a prusa mini and an easythreed x7I owned a micro3d plus printer which is dead now.. (sadface) cannot make it work again... I have a velleman K8200...
I have a Ph D in science and I am a martial artist. I survived a health accident and I am almost back to normal.
I wad looking for a solution to A) read the extruder motor input of the prusa mini to run another extruder. as a direct drive instead. I have bought an extra extruder from easythreed in order to do that at some point and B) I want to tune my printer using instant shaping: for that I need a accelerometer that can measure vibration of the printer: therefore M5 stack coimes probably as a good idea...
thx Adam....As you said I found it..
I still do not know why it is not workimg with atom s3
voila
Ok thks adam.
By the way i have a m5stick cplus. I could burn uiflow on it.
Does it mean then i can install any program made with uiflow on it?without needing to install the program via m5burner?from uiflow.
I am looking for the key of each part cannot find those i have the sn feom the label ...
By the way i printed the part yesterday and i neede to scale it a bit to fit the tailbat and a m5atom s3. Thank you for that you saved me time also i had to print it 3 times before getting the right dimensions.
It may be due to my printer tolerances! I will send you the dimension i used. Bye
Frog
Hi Adam, so: I unzip my file in programm subfolder.
open M5nurner .exe as administrator.I can update firmware list.... but still looking for the same patch in the unzipped folder: I have anotherjavascript error message:: It is not EPERM but ENOENT..
However I connected the s3 to it. and push the left side button until green led flashes....then connect com6 (the detected port com there it is green) It fails to erase or to burn. failed to get mac. also when reducing the baud rate to 11000..
I tried even the easyloader software without success...
I found you and let you a comment on your atom choacker building block
For me I am pissed off by obsolescence... and therefore I gather reusable trash from the street I f I see a possibility to do ...
I like repair stuff. and understand thing...
I just search for you on thingiverse not able to find you
look for "micro handle repair with storm Mando helmet low poly"
did you made a design? what tittle?
Hi Adam,
I am french living in Zurich and interested in dIY stuff I own 2 3d printer and having 2 that are dust trap (one is broken ( a crap m3d printer micro...not repaire-able ) but ok... I design more than 70 opensource design to be 3d printed.... I have assembled a nerdy gurdy for which I designed additionnal thingiverse models... I am active on the prusa community forum... I wanted to programm a xyz accelerometer export to enable easy instant shaping...
Hi adam, I saw your review of cores3, sad that this part is not as straight foreward as one can expect.if i reckon correctly you struggled to get uiflow burned to the device as well. I did not get gow you did it!
But you erase first the mwmory using m5 burner.
The boot load mode was quite tricky to trigger.seems like
On the atom s3 i need to press the side button for 3 seconds and a green led is shining for 2 secs i however do not know if you started thw mode. It stays in this mode untill you power off.
As it is not a msi installer but just an exe i had never a problem running an exe not from the program files folder. Also from the temp folder.
It is not playing a role sofar. This would be for me the first time.... if this is mandatory one must write a step by step standard procedure as idiot proof as possible...
Nevertheless i an sure trying to extract into the program file folder will not solve the missing patch file...my honest opinion.