[Solved]M5Stick and VL53L1X
-
Hi all,
I'm trying VL53L1X sensor on M5Stick through grove connection
VL53L1X---------------------M5Stick
VIN-------------------------------5v grove
GRD-------------------------------grd grove
SDA--------------------------------G21 grove
SCL---------------------------------G22 groveuploading this sketch
/* This example shows how to take simple range measurements with the VL53L1X. The range readings are in units of mm. */ #include <Wire.h> #include <VL53L1X.h> VL53L1X sensor; void setup() { Serial.begin(115200); Wire.begin(); Wire.setClock(400000); // use 400 kHz I2C sensor.setTimeout(500); if (!sensor.init()) { Serial.println("Failed to detect and initialize sensor!"); while (1); } // Use long distance mode and allow up to 50000 us (50 ms) for a measurement. // You can change these settings to adjust the performance of the sensor, but // the minimum timing budget is 20 ms for short distance mode and 33 ms for // medium and long distance modes. See the VL53L1X datasheet for more // information on range and timing limits. sensor.setDistanceMode(VL53L1X::Long); sensor.setMeasurementTimingBudget(50000); // Start continuous readings at a rate of one measurement every 50 ms (the // inter-measurement period). This period should be at least as long as the // timing budget. sensor.startContinuous(50); } void loop() { Serial.print(sensor.read()); if (sensor.timeoutOccurred()) { Serial.print(" TIMEOUT"); } Serial.println(); }
this is the serial monitor output...
rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00 mode:DIO, clock div:1 load:0x3fff0018,len:4 load:0x3fff001c,len:1100 load:0x40078000,len:9220 load:0x40080400,len:6300 entry 0x400806a4 Failed to detect and initialize sensor!
whats wrong??
-
M5Stick GROVE Interface SCL: GPIO13, SDA: GPIO25. Look at M5Stick doc
-
-
-
I cant remember the exact code but you need to add
Wire1.begin();
Note the 1!its something like
Wire1.begin(13, 25);
that you need to add afterWire.begin();
Sorry, I lost my source so cant remember how I solved it.
-
-
Tnks a lot guys!!!!
I will try asaic....
-
/* This example shows how to take simple range measurements with the VL53L1X. The range readings are in units of mm. */ #include <Wire.h> #include <VL53L1X.h> VL53L1X sensor; void setup() { Serial.begin(115200); //Wire.begin(); Wire.begin(25, 13); // (SDA, SCL) grove stick //Wire.begin(21, 22); // (SDA, SCL) grove stack Wire.setClock(400000); // use 400 kHz I2C sensor.setTimeout(500); if (!sensor.init()) { Serial.println("Failed to detect and initialize sensor!"); while (1); } // Use long distance mode and allow up to 50000 us (50 ms) for a measurement. // You can change these settings to adjust the performance of the sensor, but // the minimum timing budget is 20 ms for short distance mode and 33 ms for // medium and long distance modes. See the VL53L1X datasheet for more // information on range and timing limits. sensor.setDistanceMode(VL53L1X::Long); sensor.setMeasurementTimingBudget(50000); // Start continuous readings at a rate of one measurement every 50 ms (the // inter-measurement period). This period should be at least as long as the // timing budget. sensor.startContinuous(50); } void loop() { //Serial.print(sensor.read()); //MM Serial.print(sensor.read()/10); //CM if (sensor.timeoutOccurred()) { Serial.print(" TIMEOUT"); } Serial.println(); }
it works!!!
-
@cepics said in [Solved]M5Stick and VL53L1X:
/* This example shows how to take simple range measurements with the VL53L1X. The range readings are in units of mm. */ #include <Wire.h> #include <VL53L1X.h> VL53L1X sensor; void setup() { Serial.begin(115200); //Wire.begin(); Wire.begin(25, 13); // (SDA, SCL) grove stick //Wire.begin(21, 22); // (SDA, SCL) grove stack Wire.setClock(400000); // use 400 kHz I2C sensor.setTimeout(500); if (!sensor.init()) { Serial.println("Failed to detect and initialize sensor!"); while (1); } // Use long distance mode and allow up to 50000 us (50 ms) for a measurement. // You can change these settings to adjust the performance of the sensor, but // the minimum timing budget is 20 ms for short distance mode and 33 ms for // medium and long distance modes. See the VL53L1X datasheet for more // information on range and timing limits. sensor.setDistanceMode(VL53L1X::Long); sensor.setMeasurementTimingBudget(50000); // Start continuous readings at a rate of one measurement every 50 ms (the // inter-measurement period). This period should be at least as long as the // timing budget. sensor.startContinuous(50); } void loop() { //Serial.print(sensor.read()); //MM Serial.print(sensor.read()/10); //CM if (sensor.timeoutOccurred()) { Serial.print(" TIMEOUT"); } Serial.println(); }
it works!!!
Glad it works and sorry for posting the pins the wrong way around.