PLC Module



  • I am converting a project from a raw esp32 module/MAX 485 driver -> modbus to M5Stack/PLC module.

    Does the PLC module supply power to the CPU from the 24V input?

    Is there an RTS Control line for the RS485 converter or is RTS Control automatic?

    (RTS Control is a method with which the RS232 device (typically a PC) tells an RS232-RS485 converter when it should enable its RS485 driver, i.e. when it should be transmitting. http://www.kksystems.com/rtscontrol )

    Is there a chip specification for the 485 converter? Which is used?



  • Looks like the 485 driver is a Exar SP3485.
    Some vendor on Alibaba claims it is max3485esa replacement.

    https://datasheet4u.com/datasheet-pdf-file/1103288/Exar/SP3485/1

    The SP3485 chip has
    Pin 1 - RO - Receiver output
    Pin 2 - RE - Receiver Output Enable Active LOW
    Pin 3 - DE - Driver Output Enable Active HIGH
    Pin 4 - DI - Driver Input
    Pin 5 - GND - Ground Connection
    Pin 6 - A - Non-Inverting Driver Output/Receiver Input
    Pin 7 - B - Inverting Driver Output/Receiver Input
    Pin 8 - Vcc - Positive Supply

    What pin is DE - Driver enable?

    Pin 1 - RO -> G16
    Pin 2 - RE -> ???
    Pin 3 - DE -> ???
    Pin 4 - DI -> G17
    Pin 5 - GND -> (output port G)
    Pin 6 - A -> (output port A)
    Pin 7 - B -> (output port B)
    Pin 8 - Vcc - 5V (?)

    Is there a schematic for the little module?

    alt text



  • I note that the vendor on Amazon is responsive, but not very technical or knowledgeble about the PLC module.

    Gave me the schematic for the M5 Core, not the PLC module.

    They suggested the ILI9341 (display) RST pin is what I was looking for. No. That's not quite right.



  • I'm waiting for a response supplier via vendor, who assures me that the supplier says it should work as it is and that I don't need RTS. I pointed out that the ESP-IDF documentation for UART indicates that RS485 Half Duplex requires a RTS pin (https://docs.espressif.com/projects/esp-idf/en/latest/api-reference/peripherals/uart.html):

    0_1535921034241_esp-idf-uart-snip.png

    0_1535920297908_PLCModuleModule.png
    0_1535920306839_exar-sp3485-pinout.png

    I think I'm going to have to tie a wire between the DE pin on the 3485 to a free GPIO to get the functionality I need.

    Hopefully the supplier will eventually provide some official documentation or schematics. I suspect that this might be what you get.

    Is anyone from M5Stack here?



  • @mkellner Automatic control of RS485 transceiver data



  • 0_1535952200325_1535952159(1).png



  • 此回复已被删除!


  • @mkellner Please refer to this schematic diagram.



  • @osmarPLC Module 中说:

    @mkellner Please refer to this schematic diagram.

    Thank you for responding!



  • @mkellner
    Yes the two power pins can supply the complete module, I am using 12V for the ones I have which will also power a LoRa module.
    As already answered yes it is automatic, just transmit the data and it is sent out, I am using a Modbus protocol based on one of the Arduino Libraries but it needed a lot of changing to make it compatible with the M5Stack. Works with some Smart Meters I am working with running on the second core of the ESP32 with WiFi and Screen handling on the main Arduino core.

    You need to make sure you connect all ten connections between the sub board and the main board, there were no instructions with my units so I had to figure them all out. A, B, C and D next to the connector, 5V and GND to the top left of the connector, Vin T2 and R2 on the left side of the main M5Stack connector and if you want to use the current measurement you need to connect pin34 on the right hand side of the main connector. I found the easiest way was to use 0.1" pitch pins and solder them to the small board first and then the main board.

    The current measurement is done by the other chip on the small board, it appears to be the current flow into the whole system if the unit is powered from the external power connections marked 24V and G


登录后回复
 

与 M5Stack Community 的连接断开,我们正在尝试重连,请耐心等待