UIFlow2.0 could not burnned correctly into M5Stack basic(Core)

[ymd_m]

Hello

I tried to burn UIFlow2.0(v2.0.4-16MB) with M5burner but it seems not correctly burned.
Below is the result of M5burner. I feel M5burner burned very small amount.
(It wrote just only 24576bytes)
Also I tried to burn UIflow1, then it worked fine, no problem.
Additionally I tested with AtomS3U/UIFlow2.0.4. It also no problem.

Could someone please help me?
What settings should I check?

----------result of burn UIFlow2.0.4 into M5Stack basic----
Detecting chip type...
ESP32
Chip is ESP32-D0WDQ6-V3 (revision v3.0)
Features: WiFi, BT, Dual Core, 240MHz, VRef calibration in efuse, Coding Scheme None
Crystal is 40MHz
MAC: 78:21:84:a6:58:4c
Uploading stub...
Running stub...
Stub running...
Configuring flash size...
Auto-detected Flash size: 16MB
Flash will be erased from 0x00009000 to 0x0000efff...
Compressed 24576 bytes to 470...
Writing at 0x00009000... (100 %)
Wrote 24576 bytes (470 compressed) at 0x00009000 in 0.3 seconds (effective 569.3 kbit/s)...
Hash of data verified.

Leaving...
Hard resetting via RTS pin...

----------result of burn UIFlow1.13.4 into M5Stack basic----
Detecting chip type...
ESP32
Chip is ESP32-D0WDQ6-V3 (revision v3.0)
Features: WiFi, BT, Dual Core, 240MHz, VRef calibration in efuse, Coding Scheme None
Crystal is 40MHz
MAC: 78:21:84:a6:58:4c
Uploading stub...
Running stub...
Stub running...
Changing baud rate to 921600
Changed.
Configuring flash size...
Auto-detected Flash size: 16MB
Flash will be erased from 0x003ff000 to 0x003fffff...
Flash will be erased from 0x00000000 to 0x003fdfff...
Compressed 100 bytes to 31...
Writing at 0x003ff000... (100 %)
Wrote 100 bytes (31 compressed) at 0x003ff000 in 0.0 seconds (effective 18.3 kbit/s)...
Hash of data verified.
Compressed 4186112 bytes to 2526007...
Writing at 0x00000000... (0 %)
Writing at 0x00010bfa... (1 %)
Writing at 0x00017cfe... (1 %)
Writing at 0x00020bd2... (2 %)
.....
Writing at 0x003fd154... (100 %)
Wrote 4186112 bytes (2526007 compressed) at 0x00000000 in 40.2 seconds (effective 833.1 kbit/s)...
Hash of data verified.

Leaving...
Hard resetting via RTS pin...

----------result of burn UIFlow2.0.4 into ATOMS3U----
--chip auto --port COM5 --baud 921600 --before default_reset write_flash -z --flash_mode dio --flash_freq 80m --flash_size detect 0x000 C:\Users\ABC\Documents\M5burner\packages\tmp\uiflow2-mixin.bin
esptool.py v4.6.2
Serial port COM5
Connecting...

Detecting chip type... ESP32-S3
Chip is ESP32-S3 (revision v0.1)
Features: WiFi, BLE
Crystal is 40MHz
MAC: 70:04:1d:d3:52:48
Uploading stub...
Running stub...
Stub running...
Changing baud rate to 921600
Changed.
Configuring flash size...
Auto-detected Flash size: 8MB
Flash will be erased from 0x00000000 to 0x007fefff...
Compressed 8384512 bytes to 3140155...
Writing at 0x00000000... (0 %)
Writing at 0x000127c8... (1 %)
...
Writing at 0x0057da35... (99 %)
Writing at 0x0070947b... (100 %)
Wrote 8384512 bytes (3140155 compressed) at 0x00000000 in 36.8 seconds (effective 1820.8 kbit/s)...
Hash of data verified.

Leaving...
Hard resetting via RTS pin...

Thank you
Regards

[ajb2k3]

That says all is correct
Are you erasing before burning?
Are you making sure to burn the correct version?
What’s the problem?

[ymd_m]

Hello ajb2k3.
Thanks for your reply.

Yes, I erased before burnning.

The problem is no response when writing program into M5stack Basic with Web Terminal. (Just only displaying "Progress:" and progrss bar did not forwarding.)

It occures only combination with UIFlow2 and M5Stack basic.
(it is ok UIFlow1 and M5stack basic, also UIFlow2 and ATOMS3U is no probelm.)

Thus I assume UIFlow2 is not burnned correctly into my M5Stack Basic.
(In problem case, 24576 bytes was written. However other successed cases, 4186112bytes or 8384512 bytes written. I feel 24576bytes is too much small than oter cases. )

Also I tried to burnning UIFlow 2.0.3(4MB and 16MB) and 2.0.4(4MB and 16MB) with M5Burner but these were same result. (I tested UIFlow2.0. NOT UIFlow2.0 Fire)

So could you please let me know it you have any suggestions as to what shall I check?

Thank you
Regards

[ajb2k3]

only v2.0.4- 4MB version will work on the core, the 16MB is for the fire version.
I have the Core and the Go sat on my desk here running UIFlow 2 and I made a video on it.
https://youtu.be/Z1i93cYSPIQ?si=lDVZ7rP7oACUCaQO

[ymd_m]

@ajb2k3
Thanks for your reply.
I tried several times and found what am I wrong.

I was wrote only configuration with "Configure" button in M5burner.
Then it burned just only configuration but no other firmware.

So it should burn with "Burn" button. Then firmware and configuration were written correctly.

Thanks for your help.
Regards