Hello
I tried to burn UIFlow2.0(v2.0.4-16MB) with M5burner but it seems not correctly burned.
Below is the result of M5burner. I feel M5burner burned very small amount.
(It wrote just only 24576bytes)
Also I tried to burn UIflow1, then it worked fine, no problem.
Additionally I tested with AtomS3U/UIFlow2.0.4. It also no problem.
Could someone please help me?
What settings should I check?
----------result of burn UIFlow2.0.4 into M5Stack basic----
Detecting chip type...
ESP32
Chip is ESP32-D0WDQ6-V3 (revision v3.0)
Features: WiFi, BT, Dual Core, 240MHz, VRef calibration in efuse, Coding Scheme None
Crystal is 40MHz
MAC: 78:21:84:a6:58:4c
Uploading stub...
Running stub...
Stub running...
Configuring flash size...
Auto-detected Flash size: 16MB
Flash will be erased from 0x00009000 to 0x0000efff...
Compressed 24576 bytes to 470...
Writing at 0x00009000... (100 %)
Wrote 24576 bytes (470 compressed) at 0x00009000 in 0.3 seconds (effective 569.3 kbit/s)...
Hash of data verified.
Leaving...
Hard resetting via RTS pin...
----------result of burn UIFlow1.13.4 into M5Stack basic----
Detecting chip type...
ESP32
Chip is ESP32-D0WDQ6-V3 (revision v3.0)
Features: WiFi, BT, Dual Core, 240MHz, VRef calibration in efuse, Coding Scheme None
Crystal is 40MHz
MAC: 78:21:84:a6:58:4c
Uploading stub...
Running stub...
Stub running...
Changing baud rate to 921600
Changed.
Configuring flash size...
Auto-detected Flash size: 16MB
Flash will be erased from 0x003ff000 to 0x003fffff...
Flash will be erased from 0x00000000 to 0x003fdfff...
Compressed 100 bytes to 31...
Writing at 0x003ff000... (100 %)
Wrote 100 bytes (31 compressed) at 0x003ff000 in 0.0 seconds (effective 18.3 kbit/s)...
Hash of data verified.
Compressed 4186112 bytes to 2526007...
Writing at 0x00000000... (0 %)
Writing at 0x00010bfa... (1 %)
Writing at 0x00017cfe... (1 %)
Writing at 0x00020bd2... (2 %)
.....
Writing at 0x003fd154... (100 %)
Wrote 4186112 bytes (2526007 compressed) at 0x00000000 in 40.2 seconds (effective 833.1 kbit/s)...
Hash of data verified.
Leaving...
Hard resetting via RTS pin...
----------result of burn UIFlow2.0.4 into ATOMS3U----
--chip auto --port COM5 --baud 921600 --before default_reset write_flash -z --flash_mode dio --flash_freq 80m --flash_size detect 0x000 C:\Users\ABC\Documents\M5burner\packages\tmp\uiflow2-mixin.bin
esptool.py v4.6.2
Serial port COM5
Connecting...
Detecting chip type... ESP32-S3
Chip is ESP32-S3 (revision v0.1)
Features: WiFi, BLE
Crystal is 40MHz
MAC: 70:04:1d:d3:52:48
Uploading stub...
Running stub...
Stub running...
Changing baud rate to 921600
Changed.
Configuring flash size...
Auto-detected Flash size: 8MB
Flash will be erased from 0x00000000 to 0x007fefff...
Compressed 8384512 bytes to 3140155...
Writing at 0x00000000... (0 %)
Writing at 0x000127c8... (1 %)
...
Writing at 0x0057da35... (99 %)
Writing at 0x0070947b... (100 %)
Wrote 8384512 bytes (3140155 compressed) at 0x00000000 in 36.8 seconds (effective 1820.8 kbit/s)...
Hash of data verified.
Leaving...
Hard resetting via RTS pin...
Thank you
Regards