M5Dial UART Write not sending data

xbr11332003

The following M5Dial/UIFlow 2.0 code is able to receive data from Arduino Uno r4 wifi, but i cannot get data to Arduino. Using basic example Arduino code that works on other devices. Am i missing something? Tried every write command in UART list.

import os, sys, io
import M5
from M5 import *
from hardware import *



label0 = None
label1 = None
label2 = None
rotary = None
uart1 = None


def btnA_wasClicked_event(state):
  global label0, label1, label2, rotary, uart1
  rotary.reset_rotary_value()
  label0.setText(str(rotary.get_rotary_value()))
  label1.setText(str(rotary.get_rotary_value()))
  print(uart1.read(1)[0])
  uart1.write(bytes([1]))


def btnA_wasHold_event(state):
  global label0, label1, label2, rotary, uart1
  label1.setText(str('hold'))
  label2.setText(str('Label'))


def setup():
  global label0, label1, label2, rotary, uart1

  M5.begin()
  Widgets.fillScreen(0x222222)
  label0 = Widgets.Label("0", 96, 80, 1.0, 0xffa000, 0x222222, Widgets.FONTS.DejaVu72)
  label1 = Widgets.Label("label1", 88, 158, 1.0, 0xffffff, 0x222222, Widgets.FONTS.DejaVu18)
  label2 = Widgets.Label("label2", -21, 114, 1.0, 0xffffff, 0x222222, Widgets.FONTS.DejaVu9)

  BtnA.setCallback(type=BtnA.CB_TYPE.WAS_CLICKED, cb=btnA_wasClicked_event)
  BtnA.setCallback(type=BtnA.CB_TYPE.WAS_HOLD, cb=btnA_wasHold_event)

  label1.setColor(0xcc33cc, 0x33ff33)
  rotary = Rotary()
  uart1 = UART(1, baudrate=9600, bits=8, parity=None, stop=1, tx=13, rx=15, txbuf=256, rxbuf=256, timeout=0, timeout_char=0, invert=0, flow=0)


def loop():
  global label0, label1, label2, rotary, uart1
  M5.update()
  if rotary.get_rotary_status():
    label0.setText(str(rotary.get_rotary_value()))


if __name__ == '__main__':
  try:
    setup()
    while True:
      loop()
  except (Exception, KeyboardInterrupt) as e:
    try:
      from utility import print_error_msg
      print_error_msg(e)
    except ImportError:
      print("please update to latest firmware")

Arduino Code:

int incomingByte = 0; // for incoming serial data

void setup() {
  Serial.begin(9600); // opens serial port, sets data rate to 9600 bps
Serial1.begin(9600);
}

void loop() {
  // reply only when you receive data:
  if (Serial1.available() > 0) {
    // read the incoming byte:
    incomingByte = Serial.read();

    // say what you got:
    Serial1.print("I received: ");
    Serial1.println(incomingByte, DEC);
  }
}

xbr11332003

@xbr11332003
Tried every UART write command and arduino is not receiving data.
Serial monitor on Arduino prints -1. Again, I can send data to m5dial but arduino does not receive. Other arduino boards work flawlessly. Please help felix.

felmue

Hello @xbr11332003

have you tried to send the data with trailing CR LF? E.g. uart1.write('hallo\r\n')? Works for me.

Thanks
Felix