M5Paper error on Arduino upload
-
Hi, I have a new M5Paper 1.1 and Arduino 1.8.19.
I have selected the board M5Stack-Paper and the port.
With my M5Core2 I have no problems, but when I compile and upload any program to M5Paper I get the following error message:
Arduino: 1.8.19 (Windows 10), Board: "M5Stack-Paper, Enabled, Default (2 x 6.5 MB app, 3.6 MB SPIFFS), 240MHz (WiFi/BT), 921600, None"Sketch uses 415801 bytes (6%) of program storage space. Maximum is 6553600 bytes.
Global variables use 18392 bytes (0%) of dynamic memory, leaving 4503592 bytes for local variables. Maximum is 4521984 bytes.
usage: esptool write_flash [-h] [--erase-all]
[--flash_freq {keep,80m,60m,48m,40m,30m,26m,24m,20m,16m,15m,12m}]
[--flash_mode {keep,qio,qout,dio,dout}]
[--flash_size FLASH_SIZE]
[--spi-connection SPI_CONNECTION] [--no-progress]
[--verify] [--encrypt]
[--encrypt-files <address> <filename> [<address> <filename> ...]]
[--ignore-flash-encryption-efuse-setting]
[--compress | --no-compress]
<address> <filename> [<address> <filename> ...]esptool write_flash: error: argument <address> <filename>: Address "{upload.erase_cmd}" must be a number
esptool write_flash: error: argument <address> <filename>: Address "{upload.erase_cmd}" must be a numberCan anyone help with this?
-
@gordond You haven't selected the com port that the m5Paper is connected to.
-
Hi, when I plug in M5Paper COM port 6 appears and I have selected it, but still get that error message.
I have also used Easyloader to upload Calculator and Factory Test successfully and that showed COM port 6.
-
can you capture the beginning of the write attempt just after compile?
-
During compile I found this error message:
Multiple libraries were found for "SD.h"
Used: C:\Users\Gordon\AppData\Local\Arduino15\packages\m5stack\hardware\esp32\2.0.5\libraries\SD
Not used: C:\Program Files (x86)\Arduino\libraries\SD
Multiple libraries were found for "WiFiClient.h"
Used: C:\Users\Gordon\AppData\Local\Arduino15\packages\m5stack\hardware\esp32\2.0.5\libraries\WiFi
Not used: C:\Program Files (x86)\Arduino\libraries\WiFi
"C:\Users\Gordon\AppData\Local\Arduino15\packages\m5stack\tools\xtensa-esp32-elf-gcc\gcc8_4_0-esp-2021r2-patch3/bin/xtensa-esp32-elf-ar" cr "C:\Users\Gordon\AppData\Local\Temp\arduino_build_476900\core\core.a" "C:\Users\Gordon\AppData\Local\Temp\arduino_build_476900\core\esp32-hal-rgb-led.c.o"
remove core\core.a: The process cannot access the file because it is being used by another process.
"C:\Users\Gordon\AppData\Local\Arduino15\packages\m5stack\tools\xtensa-esp32-elf-gcc\gcc8_4_0-esp-2021r2-patch3/bin/xtensa-esp32-elf-ar" cr "C:\Users\Gordon\AppData\Local\Temp\arduino_build_476900\core\core.a" "C:\Users\Gordon\AppData\Local\Temp\arduino_build_476900\core\esp32-hal-rmt.c.o"
Error compiling for board M5Stack-Paper.and then after compile I get this:
"C:\Users\Gordon\AppData\Local\Arduino15\packages\m5stack\tools\xtensa-esp32-elf-gcc\gcc8_4_0-esp-2021r2-patch3/bin/xtensa-esp32-elf-size" -A "C:\Users\Gordon\AppData\Local\Temp\arduino_build_476900/M5Paper_Hello_World.ino.elf"
Sketch uses 415801 bytes (6%) of program storage space. Maximum is 6553600 bytes.
Global variables use 18392 bytes (0%) of dynamic memory, leaving 4503592 bytes for local variables. Maximum is 4521984 bytes.
C:\Users\Gordon\AppData\Local\Arduino15\packages\m5stack\tools\esptool_py\3.3.0/esptool.exe --chip esp32 --port COM6 --baud 921600 --before default_reset --after hard_reset write_flash {upload.erase_cmd} -z --flash_mode dio --flash_freq 80m --flash_size 16MB 0x1000 C:\Users\Gordon\AppData\Local\Temp\arduino_build_476900/M5Paper_Hello_World.ino.bootloader.bin 0x8000 C:\Users\Gordon\AppData\Local\Temp\arduino_build_476900/M5Paper_Hello_World.ino.partitions.bin 0xe000 C:\Users\Gordon\AppData\Local\Arduino15\packages\m5stack\hardware\esp32\2.0.5/tools/partitions/boot_app0.bin 0x10000 C:\Users\Gordon\AppData\Local\Temp\arduino_build_476900/M5Paper_Hello_World.ino.bin
usage: esptool write_flash [-h] [--erase-all]
[--flash_freq {keep,80m,60m,48m,40m,30m,26m,24m,20m,16m,15m,12m}]
[--flash_mode {keep,qio,qout,dio,dout}]
[--flash_size FLASH_SIZE]
[--spi-connection SPI_CONNECTION] [--no-progress]
[--verify] [--encrypt]
[--encrypt-files <address> <filename> [<address> <filename> ...]]
[--ignore-flash-encryption-efuse-setting]
[--compress | --no-compress]
<address> <filename> [<address> <filename> ...]
esptool write_flash: error: argument <address> <filename>: Address "{upload.erase_cmd}" must be a number
esptool write_flash: error: argument <address> <filename>: Address "{upload.erase_cmd}" must be a number
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login