Posts made by marnix201

@felmue

Any updates on this @m5stack ?, does anyone know when this will be working again?

Thanks,
Marnix

@felmue

Thank you for testing.
I used lots of M5StampPico's and never had this issue before...
Do you think it will be fixed any soon ?

I especially avoid using UIflow 2 because unfortunately a lot of functions are still missing...
I would like to use the remote+ funtion and/or Blynk but both of these are not available for UIFlow 2...

So for now I guess I'm stuck on using UIFlow 1..

Hi all,

I have a problem with a M5Stamp Pico.
When I power it up it successfully connects to the internet (with the provided credentials in M5Burner) but after that the LED stays SOLID Blue no matter what I'll do, so it will never get to the "Flashing green" status. (I uploaded the latest UIflow Firmware) (Not UIFlow 2.0 but just UIFlow 1)

I tried reflashing it a couple of times, connect to different routers, tried different firmwares, I even tried other M5Stamp-Pico's, but I have the exact same problem with all of them. (They are all of the same 5 pack I ordered recently)

Could it be a server problem or something ?

Thanks,
Marnix.

@felmue

Okay, I will try to do that once I've got the required HW and SW to do so.
Thanks for the tip.

@felmue

Thanks for trying.

It's working now... and I feel so dumb 🤦‍♂️
I just realized that the one thing I didn't checked was the Power Supply..., it looks like my Power Supply did not deliver an high enough voltage for the PPS-Module to be stable... although it should have according to the specs.

Do you guys know of a way to "revive" or "re-flash" the 2 broken PPS-Modules that I've tried to update to the latest firmware ?

@felmue

Yes it is securely stacked to the CoreS3 with the supplied screws, it's really going nowhere.

I tried 3 different PPS-Modules now and all have the exact same problem unfortunately...

@kuriko

I did already try downgrading...

I even did try it using Arduino code, and I get the exact same results which is inconsistency in the communication (also when performing an I2C scan with Arduino)

@Bipman

Do other devices work / get recognized by your PC with the exact same cable ?
Try to use another USB Cable, some Cables only have power in them and no Data wires.

Try different ones (USB C to USB C, USB C to USB A )
Maybe try to connect it to another PC or Laptop ?

Also: try to check your Device manager to see if anything changes while plugging / unplugging the device, maybe it's a driver problem (altho normally you won't need any drivers for the S3 Devices)

@Bipman

Hi Bipman,

Make sure you follow the steps below:

1. Connect the device to your PC via USB
2. Turn on the device (via the BOOT button on the top left) and wait for it to boot.
3. Now press the RESET button on the bottom right until the green light comes on and then release the button.

The screen should stay black now (backlight will be on though), this means you're in programming mode.

Also very important: download the latest M5Burner tool from the M5Stack website: https://docs.m5stack.com/en/uiflow/m5burner/intro
Else it won't work either.

@marnix201 said in PPS 13.2 Module not working properly:

Hi all,

I ordered a couple of Module13.2 PPS (SKU:M137) modules for use with the M5Stack CoreS3 main units.
Unfortunately I can't get it to work, when I upload a "Default" test code (Initialize the unit, set output to True and after that Set the current and voltage to desired levels) sometimes it works just one time, but most of the time the module does not respond, or it says: Module not found.

I also tried scanning for I2C devices and I found out that the address is not present all the time, it fluctuates between present and not present, this does not happen with other I2C devices on the same bus, I of course use the standard address: 0x35 and i have a stable 24V on the DC-in connector (1A capable) and no load attached to the output.

I tried many different controllers and many different PPS-modules with and without other devices on the bus, but unfortunately they all give the exact same results....

I also tried flashing the firmware update from the official website because I hoped this would help increasing the communication stability of the PPS-module, but by doing this I bricked already 2 of my PPS-modules =( , after the update I cannot find them anymore while scanning the I2C bus for devices....

The Link to the Firmware updater: [https://m5stack.oss-cn-shenzhen.aliyuncs.com/resource/docs/products/module/M137 Module13.2-PPS/pps_upgrade_v1_esp32s3.exe](link url)

Can someone please help me with this ?, and can my "bricked" devices still be fixed ? =(.....

Thank you,
Marnix.

( All of the above is tried using UIFlow 2 by the way.
I also tried it using custom commands via the I2C module in UIFlow but I get the exact same results (sometimes it works but most of the time the PPS-module does not respond to commands)

This is the result of scanning I2C devices with the PPS-Module attached:

It's all about the "53" which is 0x35 in HEX (The address of the PPS-module)
You see that it's not constantly available and this is why the communication often doesn't work...

Hi all,

I ordered a couple of Module13.2 PPS (SKU:M137) modules for use with the M5Stack CoreS3 main units.
Unfortunately I can't get it to work, when I upload a "Default" test code (Initialize the unit, set output to True and after that Set the current and voltage to desired levels) sometimes it works just one time, but most of the time the module does not respond, or it says: Module not found.

I also tried scanning for I2C devices and I found out that the address is not present all the time, it fluctuates between present and not present, this does not happen with other I2C devices on the same bus, I of course use the standard address: 0x35 and i have a stable 24V on the DC-in connector (1A capable) and no load attached to the output.

I tried many different controllers and many different PPS-modules with and without other devices on the bus, but unfortunately they all give the exact same results....

I also tried flashing the firmware update from the official website because I hoped this would help increasing the communication stability of the PPS-module, but by doing this I bricked already 2 of my PPS-modules =( , after the update I cannot find them anymore while scanning the I2C bus for devices....

The Link to the Firmware updater: [https://m5stack.oss-cn-shenzhen.aliyuncs.com/resource/docs/products/module/M137 Module13.2-PPS/pps_upgrade_v1_esp32s3.exe](link url)

Can someone please help me with this ?, and can my "bricked" devices still be fixed ? =(.....

Thank you,
Marnix.