M5Stack - Simple Applications for RFID- Arduino



  • HI,
    I would like to connect a RFID reader to a M5Stack, I have a RC522 sensor witch is connected like this SDA to SDA, SCK to SCK, MOSI to MO, MI to MI, Reset to 1. I have this code:

    #include <SPI.h>
    #include <MFRC522.h>
    #include <M5Stack.h>

    #define RST_PIN 1 //Pin 1 para el reset del RC522
    #define SS_PIN 21 //Pin 21 para el SS (SDA) del RC522
    MFRC522 mfrc522(SS_PIN, RST_PIN); //Creamos el objeto para el RC522

    void setup() {
    M5.begin();
    Serial.begin(9600); //Iniciamos la comunicación serial
    SPI.begin(); //Iniciamos el Bus SPI
    mfrc522.PCD_Init(); // Iniciamos el MFRC522
    Serial.println("Lectura del UID");
    M5.Lcd.println("Lectura del UID");
    }

    void loop() {
    // Revisamos si hay nuevas tarjetas presentes
    if ( mfrc522.PICC_IsNewCardPresent())
    {
    //Seleccionamos una tarjeta
    if ( mfrc522.PICC_ReadCardSerial())
    {
    // Enviamos serialemente su UID
    Serial.print("Card UID:");
    M5.Lcd.println("Card UID:");
    for (byte i = 0; i < mfrc522.uid.size; i++) {
    Serial.print(mfrc522.uid.uidByte[i] < 0x10 ? " 0" : " ");
    M5.Lcd.print (mfrc522.uid.uidByte[i] < 0x10 ? " 0" : " ");
    Serial.print(mfrc522.uid.uidByte[i], HEX);
    M5.Lcd.print (mfrc522.uid.uidByte[i], HEX);
    }
    Serial.println();
    M5.Lcd.println();
    // Terminamos la lectura de la tarjeta actual
    mfrc522.PICC_HaltA();
    }
    }
    ´´
    Unfortunately does not work.
    Please, could somebody give me an advise, something simple...
    In the future I want to create a door access.
    Thank you in advance.


  • M5Stack

    pin 1 is for serial0, maybe not good for this.



  • #define RST_PIN 1 //Pin 1 para el reset del RC522

    As @m5stack said, PIN 1 is used by Serial0. You should pick a GPIO that's not in use already.



  • @dda Are there any other solucions to connect RFID to M5Stack?



  • @ddaniel Read my answer again: don't use pin 1 for RST_PIN. Connect it to another pin that isn't used yet.



  • I am interested in a compact RFID reader with a feedback display.
    I am wondering whether you have managed to build the sensor into the stack or whether it needs to be put off to the side somewhere?



  • @dave Hi Dave,

    I have a RFID-RC522 module on order but hasn't arrived yet... Apparently the board dimensions are: 3.9 x 6 cm

    So unfortunately it seems the whole module won't fit inside the M5 case....

    Might be ok with just a little sticking out the side....



  • You could take a look at https://www.sparkfun.com/products/11828

    It is somewhat more expensive, but has a body type that may be able to fit just fine into a different stack, or even the protoboard. They have other models as well.



  • @jp128 @Dave @ddaniel

    Hi Jp128,
    Thanks for the tip..... could be very useful.... more reading required....


Log in to reply
 

Looks like your connection to M5Stack Community was lost, please wait while we try to reconnect.