Static IP?
TOF units are I2C devices so require I2C addresses.
What hub are you trying to use as you need a PAHub that will change the addresses to 0x70 to 0x76 (I think)
Posts made by ajb2k3
-
RE: Static IP wifi with UIFLOW 1
-
RE: M5Stickc plus2 Black Screen After Factory Reset
There are 3 versions of the StickC, make sure you burn the correct firmware version for your stickC
-
RE: Help on M5STICKS plus.
Have you configured Arduino with the Board definition and support libraries?
What error messages are you getting?
What Arduino version?
What computer, OS ?
Have you installed any required device drivers?We need more information before we can accurately provide help!
-
RE: Thermal Camera 2 with Cardputer CODE
Have you tried searching first places like the M5Stack website and GITHub?
-
RE: M5StickC Plus2 Stopped Connecting
Have you tried putting the stick into download mode?
-
Burning Firmware to the StickCPlus2
Burning Firmware to the #M5Stack StickCPlus2 https://youtu.be/dtWpsZJ0urs
-
RE: [Documentation] AtomS3 Schematics
@ifantus Yeh, I'm the Mod of the communities.
They do visit the forums but they have been busy with travel. -
RE: M5Burner Error Burn Bin to Cardputer After Burn UIFlow2.0
@lamfan it is there in M5Burner already (or was last time I checked
-
RE: UnitCamS3 Trouble programming in Arduino IDE and getting 2mp image
can you post the link?
-
RE: Stamp IO to create additional serial interfaces
It is possible as the stamp IO is a reprogrammable STM32f03
-
RE: M5Burner Error Burn Bin to Cardputer After Burn UIFlow2.0
@lamfan You need to put the cardputer into "Bootloader" mode to burn firmware.
-
How to get started with the M5GO IOT Starter KIT
Let's get started with the #M5Stack #M5GO #IOT Starter KIT. https://www.hackster.io/AJB2K3/m5go-iot-starter-kit-part-1-8ef6ae
-
RE: SensorHub
@idefixcert As long as devices have different address (and sufficient power) up to 200 devices can connect to the I2C bus (I think)
-
RE: [Documentation] AtomS3 Schematics
@saiyande I would hazard a guess that its because the same PCBis used for the AtomS3 and the AtomS3lite version.
-
RE: M5card computer
Have you charged it?
-
RE: 質問:AirQの振る舞いについて
@m5uiflowhamuzui00 said in 質問:AirQの振る舞いについて:
M5Stackを数か月前から始めた初心者です。
黄砂がきになり、思い切ってAirQを購入いたしました。
取説を見ながら設定を進め、スマホとつながり測定値を読むことまではできました。
次に、USB給電を行うと画面が乱れ、動作も遅くなる現象が生じました。USBを外すと画面の乱れは直ります。
試しに M5 Burner を用いて AirQ の AirQ-UserDemo V.0.1.1 を書き込んだところ、USB給電時の画面の乱れは解消しましたが、以下の気になる点が生じました。
・VOCとNOxのデータが取得できていなさそう
・AirQ本体の時間表示がGMT +9 に変更されない
購入時のプログラムとV0.1.1の差など、AirQ に関しての情報をお持ちの方がいらっしゃいましたら、ご教授を賜れましたら幸いです。
どうぞよろしくお願いいたします。画面の乱れは正常に動作するようになっています。
タイムゾーンはファームウェアにハードコーディングされます。 -
RE: New Core2 not turning on
Use M5Burner to erase the firmware and burn UIFLOW2 for Core2/Core2AWS.
once the process is complete and the button turn green, close M5Burner and press the reset button. -
RE: Powering Core 2 using battery connector?
The Best way is to connect the power through the MBUS in the underside